KSh250.00 + VAT
MUS156 Spare En54-11 Glass Pack For Mcp
SKU: MUS15610 Spare breakable glass pack for Morley-IAS addressable manual call points.
KSh457.89 + VAT
SR1T Morley Call Point Backbox For Surface Mounting
SKU: SR1T- Manufacturer : Morley by Honeywell
- Part Number : SR1T / PS031W
- Surface Mounted Call Point Backbox
KSh595.26 + VAT
PS200 KAC – Fire Alarm Call Point Cover
SKU: PS200The KAC call point cover part number PS200; will fit all types of KAC call points including the old flat type to the new curved type.
KSh610.53 + VAT
B501AP-IV Detector Base
SKU: B501AP-IV- The Notifier B501AP-IV Detector Base is an analogue addressable detector base. This base comes in Ivory to match the Ivory detectors in the Notifier range.
KSh610.53 + VAT
M200E-SMB Morley Surface Mounting Box
SKU: M200E-SMBSurface mounting box for M7xx series modules.
KSh712.28 + VAT
WRR Morley Intelligent Loop Sounder Base
SKU: WRRFeatures
- Loop powered
- Low current draw enables more devices on loop
- Adjustable volume control on device
- Intense strobe output
- Faster installation
- Large cable access
- Rear or surface cable entry
- Loop continuity spring
- Automatic synchronisation of sounder and strobe
KSh814.04 + VAT
B401 System Sensor Plug-In Detector Base
SKU: B401Specifications
- Base Diameter: 10.2 cm (4.0 inches)
- Base Height: 2.0 cm (0.8 inches)
- Weight: 152 g (0.34 lb.)
- Mounting: 50 mm box 60 mm box Operating
- Temperature Range: –10° to +60°C (14° to 140°F) — European Installation 0° to 49°C (32° to 120°F) — US/Australian Installation Operating Humidity
- Range: 10% to 93% Relative Humidity
KSh1,526.32 + VAT
M1A-Y470SG-K013-14 KAC Red Surface Call Point 470 Ohm
SKU: M1A-Y470SG-K013-14-
KAC Callpoints are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
KSh1,670.69 + VAT
KAC MCP1A-Y470SG-14 Yellow Extinguishant Release Call Point
SKU: N/A- Manufacturer : KAC
- Part Number : MCP1A-Y470SG-14
- Yellow Extinguishant Release Call Point Unit
- Surface Mounted Version – Supplied With Backbox
- Supplied With Frangible Glass Element & Test / Reset Key
- 470Ohm Resistor & NO Contact
KSh1,729.82 + VAT
MCP1A-R470FG-01 Honeywell Conventional Flush Call Point Notifier
SKU: MCP1A-R470FG-01Notifier MCP1A-R470FG-01 Conventional Flush Call Point with 470 Ohm Resistor
The MCP1A-R470 ranges are manual call points, both with a 470 Ohm resistor and Normally Open contact, complete with glass. The MCP1A-R470FG-01 is designed for semi flush mounting and the MCP1A-R470SG-01 is designed for surface mounting. The call points are designed to provide a manual alarm interface to non-addressable fire alarm control panels. MCP1A-R470FG-01 & MCP1A-R470SG-01 call points are supplied in the standard red colour.
KSh2,035.09 + VAT
EC01003 System Sensor Conventional Optical Smoke Detector
SKU: EC01003-
Conventional optical smoke detector, automatic drift compensation, voltage 8-30VDC/ current 0,05mA quiescent and 80mA in alarm, IP43 when installed on WB-1 shroud, -30° to 70°C, certificate 0832-CPD-0064
KSh2,035.09 + VAT
RA100Z System Sensor Remote Annunciator
SKU: RA100ZRA100Z remote annunciator is designed for both conventional and intelligent applications.
KSh2,035.09 + VAT
ECO1002 System Sensor Conventional Multi-Sensor Detector – Smoke & Heat
SKU: ECO1002- Low profile design
- Low current draw
- Automatic drift compensation
- Operates on 12 and 24VDC Systems
- Remote alarm test feature
- Easy Maintenance
- Range of detector bases available
- Remote LED Option
- Approved to EN54 – 7:2000 (Amendment 1)
- EN54 – 5:2000 (Amendment 1) Class A1R; CEA 4021
KSh2,035.09 + VAT
EC01005 Honeywell TeMPerature Heat Detector
SKU: EC01005- Conventional ROR temperature Detector
KSh2,849.12 + VAT
MI-RHSE-S2-IV Morley Thermal Rate Of Rise Detector
SKU: MI-RHSE-S2-IV|
Features
|
|
| Type of Product : | Thermal Detector |
| Power Source : | 15 to 32 VDC |
| Material : | PC/ABS |
| Temperature : | Operating Temperature -30°C to 70°C |
| Humidity : | 10% to 93% Relative Humidity, Non-condensing |
KSh3,052.63 + VAT
MI-PTSE-S2-IV Morley IAS Multi Detector
SKU: MI-PTSE-S2-IV- Manufacturer : Morley by Honeywell
- Part Number : MI-PTSE-S2-IV
- Analogue Addressable Multi Detector (Smoke & Heat Sensing Elements)
- Morley IAS Protocol
- Colour : Ivory
- Requires B501AP-IV Detector Base For Mounting
KSh3,052.63 + VAT
System Sensor Metal SaMPling Tube, 8 Ft. To 12 Ft. Width
SKU: DST10Duct smoke detector accessories add functionality to the duct smoke detection system by allowing quick, convenient inspections at eye level and effective audible and visible notification options.
KSh3,157.89 + VAT
MI-DISO Morley IAS Loop Isolation Module
SKU: MI-DISOKey Features:
- DIN rail mounting option
- Surface mounting option
- Plug in connectors
- Tri-colour LED status indication
- Address selector switches visible in 2 planes
- LED status visible in 2 planes
- Approved to GEA GEI 1-082 and CEA GEI 1-084
KSh3,561.40 + VAT
74430-88NM Enscape Conventional Sounders
SKU: 74430-88NM-
Overview
ENScape Conventional Sounders are high quality devices designed to alert building occupants of an emergency. These products feature a new folded horn design, which provides outstanding sound output at low current draw. With a modern design, global tone set and extensive installer-friendly features, the ENscape sounders are the logical choice for specifiers, OEMs, installers and distributors.
Features & Benefits
- Modern design eliminates need for device orientation
- Simple and fast installation from First fix capability, allowing electrical continuity testing prior to device fitting
- Suitable for wall and ceiling mount applications
- Global tone set: 32 tones including a new bell tone
- Two stage sounders enable alert and alarm sequences to be set for phased evacuation
- Optimised for 12V and 24V systems, making the range suitable for use in fire & security applications
KSh3,561.40 + VAT
CWSO-RR-S1 Honeywell Sounder, Red
SKU: CWSO-RR-S1The acoustic alarm signaling device is EN 54-3 compliant, in red housing, and offers a selection of 32 signal tones including the DIN tone and other country-specific tones. All tones comply with EN 54-3. Configuration takes place via a 6-pin DIP switch. Up to two different signal tones may be activated. Signaling device with flat base, suitable for wall and ceiling mounting.
MUS156 Spare En54-11 Glass Pack For Mcp
10 Spare breakable glass pack for Morley-IAS addressable manual call points.
SR1T Morley Call Point Backbox For Surface Mounting
- Manufacturer : Morley by Honeywell
- Part Number : SR1T / PS031W
- Surface Mounted Call Point Backbox
PS200 KAC – Fire Alarm Call Point Cover
The KAC call point cover part number PS200; will fit all types of KAC call points including the old flat type to the new curved type.
B501AP-IV Detector Base
- The Notifier B501AP-IV Detector Base is an analogue addressable detector base. This base comes in Ivory to match the Ivory detectors in the Notifier range.
WRR Morley Intelligent Loop Sounder Base
Features
- Loop powered
- Low current draw enables more devices on loop
- Adjustable volume control on device
- Intense strobe output
- Faster installation
- Large cable access
- Rear or surface cable entry
- Loop continuity spring
- Automatic synchronisation of sounder and strobe
B401 System Sensor Plug-In Detector Base
Specifications
- Base Diameter: 10.2 cm (4.0 inches)
- Base Height: 2.0 cm (0.8 inches)
- Weight: 152 g (0.34 lb.)
- Mounting: 50 mm box 60 mm box Operating
- Temperature Range: –10° to +60°C (14° to 140°F) — European Installation 0° to 49°C (32° to 120°F) — US/Australian Installation Operating Humidity
- Range: 10% to 93% Relative Humidity
M1A-Y470SG-K013-14 KAC Red Surface Call Point 470 Ohm
-
KAC Callpoints are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
KAC MCP1A-Y470SG-14 Yellow Extinguishant Release Call Point
- Manufacturer : KAC
- Part Number : MCP1A-Y470SG-14
- Yellow Extinguishant Release Call Point Unit
- Surface Mounted Version – Supplied With Backbox
- Supplied With Frangible Glass Element & Test / Reset Key
- 470Ohm Resistor & NO Contact
MCP1A-R470FG-01 Honeywell Conventional Flush Call Point Notifier
Notifier MCP1A-R470FG-01 Conventional Flush Call Point with 470 Ohm Resistor
The MCP1A-R470 ranges are manual call points, both with a 470 Ohm resistor and Normally Open contact, complete with glass. The MCP1A-R470FG-01 is designed for semi flush mounting and the MCP1A-R470SG-01 is designed for surface mounting. The call points are designed to provide a manual alarm interface to non-addressable fire alarm control panels. MCP1A-R470FG-01 & MCP1A-R470SG-01 call points are supplied in the standard red colour.
EC01003 System Sensor Conventional Optical Smoke Detector
-
Conventional optical smoke detector, automatic drift compensation, voltage 8-30VDC/ current 0,05mA quiescent and 80mA in alarm, IP43 when installed on WB-1 shroud, -30° to 70°C, certificate 0832-CPD-0064
RA100Z System Sensor Remote Annunciator
RA100Z remote annunciator is designed for both conventional and intelligent applications.
ECO1002 System Sensor Conventional Multi-Sensor Detector – Smoke & Heat
- Low profile design
- Low current draw
- Automatic drift compensation
- Operates on 12 and 24VDC Systems
- Remote alarm test feature
- Easy Maintenance
- Range of detector bases available
- Remote LED Option
- Approved to EN54 – 7:2000 (Amendment 1)
- EN54 – 5:2000 (Amendment 1) Class A1R; CEA 4021
MI-RHSE-S2-IV Morley Thermal Rate Of Rise Detector
|
Features
|
|
| Type of Product : | Thermal Detector |
| Power Source : | 15 to 32 VDC |
| Material : | PC/ABS |
| Temperature : | Operating Temperature -30°C to 70°C |
| Humidity : | 10% to 93% Relative Humidity, Non-condensing |
MI-PTSE-S2-IV Morley IAS Multi Detector
- Manufacturer : Morley by Honeywell
- Part Number : MI-PTSE-S2-IV
- Analogue Addressable Multi Detector (Smoke & Heat Sensing Elements)
- Morley IAS Protocol
- Colour : Ivory
- Requires B501AP-IV Detector Base For Mounting
System Sensor Metal SaMPling Tube, 8 Ft. To 12 Ft. Width
Duct smoke detector accessories add functionality to the duct smoke detection system by allowing quick, convenient inspections at eye level and effective audible and visible notification options.
MI-DISO Morley IAS Loop Isolation Module
Key Features:
- DIN rail mounting option
- Surface mounting option
- Plug in connectors
- Tri-colour LED status indication
- Address selector switches visible in 2 planes
- LED status visible in 2 planes
- Approved to GEA GEI 1-082 and CEA GEI 1-084
74430-88NM Enscape Conventional Sounders
-
Overview
ENScape Conventional Sounders are high quality devices designed to alert building occupants of an emergency. These products feature a new folded horn design, which provides outstanding sound output at low current draw. With a modern design, global tone set and extensive installer-friendly features, the ENscape sounders are the logical choice for specifiers, OEMs, installers and distributors.
Features & Benefits
- Modern design eliminates need for device orientation
- Simple and fast installation from First fix capability, allowing electrical continuity testing prior to device fitting
- Suitable for wall and ceiling mount applications
- Global tone set: 32 tones including a new bell tone
- Two stage sounders enable alert and alarm sequences to be set for phased evacuation
- Optimised for 12V and 24V systems, making the range suitable for use in fire & security applications
CWSO-RR-S1 Honeywell Sounder, Red
The acoustic alarm signaling device is EN 54-3 compliant, in red housing, and offers a selection of 32 signal tones including the DIN tone and other country-specific tones. All tones comply with EN 54-3. Configuration takes place via a 6-pin DIP switch. Up to two different signal tones may be activated. Signaling device with flat base, suitable for wall and ceiling mounting.
MUS156 Spare En54-11 Glass Pack For Mcp
10 Spare breakable glass pack for Morley-IAS addressable manual call points.
SR1T Morley Call Point Backbox For Surface Mounting
- Manufacturer : Morley by Honeywell
- Part Number : SR1T / PS031W
- Surface Mounted Call Point Backbox
PS200 KAC – Fire Alarm Call Point Cover
The KAC call point cover part number PS200; will fit all types of KAC call points including the old flat type to the new curved type.
B501AP-IV Detector Base
- The Notifier B501AP-IV Detector Base is an analogue addressable detector base. This base comes in Ivory to match the Ivory detectors in the Notifier range.
WRR Morley Intelligent Loop Sounder Base
Features
- Loop powered
- Low current draw enables more devices on loop
- Adjustable volume control on device
- Intense strobe output
- Faster installation
- Large cable access
- Rear or surface cable entry
- Loop continuity spring
- Automatic synchronisation of sounder and strobe
B401 System Sensor Plug-In Detector Base
Specifications
- Base Diameter: 10.2 cm (4.0 inches)
- Base Height: 2.0 cm (0.8 inches)
- Weight: 152 g (0.34 lb.)
- Mounting: 50 mm box 60 mm box Operating
- Temperature Range: –10° to +60°C (14° to 140°F) — European Installation 0° to 49°C (32° to 120°F) — US/Australian Installation Operating Humidity
- Range: 10% to 93% Relative Humidity
M1A-Y470SG-K013-14 KAC Red Surface Call Point 470 Ohm
-
KAC Callpoints are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
KAC MCP1A-Y470SG-14 Yellow Extinguishant Release Call Point
- Manufacturer : KAC
- Part Number : MCP1A-Y470SG-14
- Yellow Extinguishant Release Call Point Unit
- Surface Mounted Version – Supplied With Backbox
- Supplied With Frangible Glass Element & Test / Reset Key
- 470Ohm Resistor & NO Contact
MCP1A-R470FG-01 Honeywell Conventional Flush Call Point Notifier
Notifier MCP1A-R470FG-01 Conventional Flush Call Point with 470 Ohm Resistor
The MCP1A-R470 ranges are manual call points, both with a 470 Ohm resistor and Normally Open contact, complete with glass. The MCP1A-R470FG-01 is designed for semi flush mounting and the MCP1A-R470SG-01 is designed for surface mounting. The call points are designed to provide a manual alarm interface to non-addressable fire alarm control panels. MCP1A-R470FG-01 & MCP1A-R470SG-01 call points are supplied in the standard red colour.
EC01003 System Sensor Conventional Optical Smoke Detector
-
Conventional optical smoke detector, automatic drift compensation, voltage 8-30VDC/ current 0,05mA quiescent and 80mA in alarm, IP43 when installed on WB-1 shroud, -30° to 70°C, certificate 0832-CPD-0064
RA100Z System Sensor Remote Annunciator
RA100Z remote annunciator is designed for both conventional and intelligent applications.
ECO1002 System Sensor Conventional Multi-Sensor Detector – Smoke & Heat
- Low profile design
- Low current draw
- Automatic drift compensation
- Operates on 12 and 24VDC Systems
- Remote alarm test feature
- Easy Maintenance
- Range of detector bases available
- Remote LED Option
- Approved to EN54 – 7:2000 (Amendment 1)
- EN54 – 5:2000 (Amendment 1) Class A1R; CEA 4021
MI-RHSE-S2-IV Morley Thermal Rate Of Rise Detector
|
Features
|
|
| Type of Product : | Thermal Detector |
| Power Source : | 15 to 32 VDC |
| Material : | PC/ABS |
| Temperature : | Operating Temperature -30°C to 70°C |
| Humidity : | 10% to 93% Relative Humidity, Non-condensing |
MI-PTSE-S2-IV Morley IAS Multi Detector
- Manufacturer : Morley by Honeywell
- Part Number : MI-PTSE-S2-IV
- Analogue Addressable Multi Detector (Smoke & Heat Sensing Elements)
- Morley IAS Protocol
- Colour : Ivory
- Requires B501AP-IV Detector Base For Mounting
System Sensor Metal SaMPling Tube, 8 Ft. To 12 Ft. Width
Duct smoke detector accessories add functionality to the duct smoke detection system by allowing quick, convenient inspections at eye level and effective audible and visible notification options.
MI-DISO Morley IAS Loop Isolation Module
Key Features:
- DIN rail mounting option
- Surface mounting option
- Plug in connectors
- Tri-colour LED status indication
- Address selector switches visible in 2 planes
- LED status visible in 2 planes
- Approved to GEA GEI 1-082 and CEA GEI 1-084
74430-88NM Enscape Conventional Sounders
-
Overview
ENScape Conventional Sounders are high quality devices designed to alert building occupants of an emergency. These products feature a new folded horn design, which provides outstanding sound output at low current draw. With a modern design, global tone set and extensive installer-friendly features, the ENscape sounders are the logical choice for specifiers, OEMs, installers and distributors.
Features & Benefits
- Modern design eliminates need for device orientation
- Simple and fast installation from First fix capability, allowing electrical continuity testing prior to device fitting
- Suitable for wall and ceiling mount applications
- Global tone set: 32 tones including a new bell tone
- Two stage sounders enable alert and alarm sequences to be set for phased evacuation
- Optimised for 12V and 24V systems, making the range suitable for use in fire & security applications
CWSO-RR-S1 Honeywell Sounder, Red
The acoustic alarm signaling device is EN 54-3 compliant, in red housing, and offers a selection of 32 signal tones including the DIN tone and other country-specific tones. All tones comply with EN 54-3. Configuration takes place via a 6-pin DIP switch. Up to two different signal tones may be activated. Signaling device with flat base, suitable for wall and ceiling mounting.
MUS156 Spare En54-11 Glass Pack For Mcp
10 Spare breakable glass pack for Morley-IAS addressable manual call points.
SR1T Morley Call Point Backbox For Surface Mounting
- Manufacturer : Morley by Honeywell
- Part Number : SR1T / PS031W
- Surface Mounted Call Point Backbox
PS200 KAC – Fire Alarm Call Point Cover
The KAC call point cover part number PS200; will fit all types of KAC call points including the old flat type to the new curved type.
B501AP-IV Detector Base
- The Notifier B501AP-IV Detector Base is an analogue addressable detector base. This base comes in Ivory to match the Ivory detectors in the Notifier range.
WRR Morley Intelligent Loop Sounder Base
Features
- Loop powered
- Low current draw enables more devices on loop
- Adjustable volume control on device
- Intense strobe output
- Faster installation
- Large cable access
- Rear or surface cable entry
- Loop continuity spring
- Automatic synchronisation of sounder and strobe
B401 System Sensor Plug-In Detector Base
Specifications
- Base Diameter: 10.2 cm (4.0 inches)
- Base Height: 2.0 cm (0.8 inches)
- Weight: 152 g (0.34 lb.)
- Mounting: 50 mm box 60 mm box Operating
- Temperature Range: –10° to +60°C (14° to 140°F) — European Installation 0° to 49°C (32° to 120°F) — US/Australian Installation Operating Humidity
- Range: 10% to 93% Relative Humidity
M1A-Y470SG-K013-14 KAC Red Surface Call Point 470 Ohm
-
KAC Callpoints are the leaders in Call Point manufacture, invented by KAC over 40 years ago they have constantly driven to improve both standards and design of the call point to this day.
KAC MCP1A-Y470SG-14 Yellow Extinguishant Release Call Point
- Manufacturer : KAC
- Part Number : MCP1A-Y470SG-14
- Yellow Extinguishant Release Call Point Unit
- Surface Mounted Version – Supplied With Backbox
- Supplied With Frangible Glass Element & Test / Reset Key
- 470Ohm Resistor & NO Contact
MCP1A-R470FG-01 Honeywell Conventional Flush Call Point Notifier
Notifier MCP1A-R470FG-01 Conventional Flush Call Point with 470 Ohm Resistor
The MCP1A-R470 ranges are manual call points, both with a 470 Ohm resistor and Normally Open contact, complete with glass. The MCP1A-R470FG-01 is designed for semi flush mounting and the MCP1A-R470SG-01 is designed for surface mounting. The call points are designed to provide a manual alarm interface to non-addressable fire alarm control panels. MCP1A-R470FG-01 & MCP1A-R470SG-01 call points are supplied in the standard red colour.
EC01003 System Sensor Conventional Optical Smoke Detector
-
Conventional optical smoke detector, automatic drift compensation, voltage 8-30VDC/ current 0,05mA quiescent and 80mA in alarm, IP43 when installed on WB-1 shroud, -30° to 70°C, certificate 0832-CPD-0064
RA100Z System Sensor Remote Annunciator
RA100Z remote annunciator is designed for both conventional and intelligent applications.
ECO1002 System Sensor Conventional Multi-Sensor Detector – Smoke & Heat
- Low profile design
- Low current draw
- Automatic drift compensation
- Operates on 12 and 24VDC Systems
- Remote alarm test feature
- Easy Maintenance
- Range of detector bases available
- Remote LED Option
- Approved to EN54 – 7:2000 (Amendment 1)
- EN54 – 5:2000 (Amendment 1) Class A1R; CEA 4021
MI-RHSE-S2-IV Morley Thermal Rate Of Rise Detector
|
Features
|
|
| Type of Product : | Thermal Detector |
| Power Source : | 15 to 32 VDC |
| Material : | PC/ABS |
| Temperature : | Operating Temperature -30°C to 70°C |
| Humidity : | 10% to 93% Relative Humidity, Non-condensing |
MI-PTSE-S2-IV Morley IAS Multi Detector
- Manufacturer : Morley by Honeywell
- Part Number : MI-PTSE-S2-IV
- Analogue Addressable Multi Detector (Smoke & Heat Sensing Elements)
- Morley IAS Protocol
- Colour : Ivory
- Requires B501AP-IV Detector Base For Mounting
System Sensor Metal SaMPling Tube, 8 Ft. To 12 Ft. Width
Duct smoke detector accessories add functionality to the duct smoke detection system by allowing quick, convenient inspections at eye level and effective audible and visible notification options.
MI-DISO Morley IAS Loop Isolation Module
Key Features:
- DIN rail mounting option
- Surface mounting option
- Plug in connectors
- Tri-colour LED status indication
- Address selector switches visible in 2 planes
- LED status visible in 2 planes
- Approved to GEA GEI 1-082 and CEA GEI 1-084
74430-88NM Enscape Conventional Sounders
-
Overview
ENScape Conventional Sounders are high quality devices designed to alert building occupants of an emergency. These products feature a new folded horn design, which provides outstanding sound output at low current draw. With a modern design, global tone set and extensive installer-friendly features, the ENscape sounders are the logical choice for specifiers, OEMs, installers and distributors.
Features & Benefits
- Modern design eliminates need for device orientation
- Simple and fast installation from First fix capability, allowing electrical continuity testing prior to device fitting
- Suitable for wall and ceiling mount applications
- Global tone set: 32 tones including a new bell tone
- Two stage sounders enable alert and alarm sequences to be set for phased evacuation
- Optimised for 12V and 24V systems, making the range suitable for use in fire & security applications
CWSO-RR-S1 Honeywell Sounder, Red
The acoustic alarm signaling device is EN 54-3 compliant, in red housing, and offers a selection of 32 signal tones including the DIN tone and other country-specific tones. All tones comply with EN 54-3. Configuration takes place via a 6-pin DIP switch. Up to two different signal tones may be activated. Signaling device with flat base, suitable for wall and ceiling mounting.